FANDOM


{{{

<B>Basic mesh commands </b> <BR>
Start with the Locustworld Wiki <BR>
http://locustworld.com/tracker/wiki?p=TipsAndTricks   <BR>
vtund    #   <br>
pingtest     #pings all the nodes<br>
speedtest  <br>
speedtest up <br>
speeddaemon  #open a shell window on router and type speeddaemon <br>
use to check mesh or backhaul <br>
<BR>
iptables -L  , #can be used to block meshboxes of the network.<br>
cwradius username password<br>
crontab -e      # Issue blocknode command here <br>
crontab -l<br>
minsig          # Same as blocknode<br>
radping      # Pings radius server<br>
ifconfig    # interface configuration, the same as the ethernet/wlan section of reporter<br>
ifconfig -a     # Determine IP address of ehternet NIC<br>
<BR>
reporter<br>
iwconfig     #shows the wireless interface configuration - many options available <br>
iwconfig wlan0 txpower auto  # Set all nodes to 'auto power', recommended default<br>
iwconfig wlan0 txpower 200mw      # Manually forcing node to 200mw<br>
iwconfig wlan0 txpower 50mw<br>
iwconfig eth0 essid any<br>
iwconfig eth0 essid "My Network"  <br>
iwconfig wlan0 essid off<br>
iwconfig eth0 freq 2.422G<br>
iwconfig eth0 channel 3<br>
iwconfig wlan0 sens 1 <br>
iwconfig wlan0 rate 1M fixed  #Force rate down on long distance links <bR>
ipconfig                # Set the node ip address <br>

http://leaf.sourceforge.net/devel/jnilo/manpages/iwconfig.html

iwlist wlan0 ap   #will show you all clients connected to the card. <br>
iwlist - useful stats from wireless interface - more info at leaf.sourceforge <br>
iwlist wlan0 scan,  #far node looks back upstream if there is noise on network<br>
                        # Shows you everything the node can see<br>

Cat /proc/aodv/monitor  # use this with Iwlist wlan0 scanning command<br>
unblock                 #commnand unblocks a node if wiana blocked it.<br>
broadunblock            # Permanent blocking of a node<br>
reporter                #gives status of all meshboxes eth0 etc.<br>
"speedtest &" on the gateway and "speeddaemon" and<br>
"speeddaemon up" on the repeater nodes.<br>
ssh       #secure shell into a meshbox and then issue command like   getandverify<br>
ssh <ipadres>  # Use for remote control of a meshbox<br>
getandverify test,   #tests to see if wiana.org is available, should say WIANA REACHABLE<br>
getandverify tobuild25dev90  ,  #to upgrade to a specific build<br>
getandverify tobuild25dev87<br>
getandverify splashpowerupdate <br>
getandverify alwaysblockbymac <br>
Does dev106 have support for the new smc2532 cards?
<p>
My node is not recognizing the new version card on 106
If these are the newer prism3 chipset cards, then you may need to issue
the following patch on dev 106:
getandverify version23prismpcmcia
</p>
checkuplinkvalidity   #after you ssh into box, should say OK.<br>
distread           #used before a 'remotemanagement' this cleans up some things.<br>
# Careful! Its is roughly the same as 'factoryreset' Seems to kill the<br>
# dhcpd.leases file (?) <br>
factoryreset       #puts meshbox back to original factory state. Will require you to<br>
          #get a new certificate again from wiana and get the wiana settings again. <br>
remotemanagement   #use this to get the Mesh node to connect to Wiana and get the latest<br>
 #settings. The Mesh node should do this automatically every 30mins, <br>
but sometimes you just #don't want to wait. <br>
sigspy     #use to check if your node can see the other nodes. Gives signal strength.<br>
arp -n     # Networking command <br>
arp - a    # Get MAC address being represented to the meshbox<br>

}}}

links Edit

Linux shell

Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.