FANDOM


{{{

Host mapping and port mapping
You can not host map a single public IP to more than one private IP,
host mapping is a ONE TO ONE mapping from one IP to another, it
directly maps all ports.
Think of it as a simple NAT'ed network, if all the ports from a single
IP are mapped to multiple IP's the data has no way of knowing where to
go. So an example of host mapping would be:
For public IP
217.x.x.50 ---> 192.168.2.30
217.x.x.51 ---> 192.168.2.60
217.x.x.52 ---> 192.168.2.90
For private IP
192.168.1.100 ---> 192.168.2.30
192.168.1.101 ---> 192.168.2.60
192.168.1.102 ---> 192.168.2.90
ALL PORTS on each IP are forwarded to the respective ports on the host
mapped IP.
If you have only one public IP available you will have to use port
mapping and of course you can not have the same port going to more than
one private IP. So an example of port mapping would be:
192.168.1.100:25 ---> 192.168.2.30:25
192.168.1.100:80 ---> 192.168.2.30:80
192.168.1.100:4662 ---> 192.168.8.10:4662
192.168.1.100:4672 ---> 192.168.8.10:4672
You will be restricted to one of each port unless you use non-standard
ports.Full details of port and host mapping including the wiana format can be
found on the WiKi.
http://cvs.locustworld.com:8088/locustworld/wiki?p=UsingHostMappings
http://cvs.locustworld.com:8088/locustworld/wiki?p=UsingPortMappings
I have been able to host map a public IP address to a private IP but
with limited success. Here is my experience... Please comment on my problems
that I have encountered below.
1: mapped a public IP in the 217. range to four private IP.s in the
following range.
these three private ips also share the same radio id.
192.168.2.30 - email server and webserver
192.168.2.60 - Radius server
192.168.2.90 - DNS Bind server with a mysql database.
this private ip is on another radio cell but is only one hop away
from the gateway same as the other three servers above.
tthis has been mapped to 192.168.8.10
I have been experimenting with opening and Closing of ports for peer
to peer on this computerI opened the needed T&CP and UDP ports but for
some reason it still gives me a low id and that the other cannot see me
as the ports still seems blocked from there ppoint of view.
from the gateway I can ping all the mapped private addresses that I have
mapped. I can also Sssh directly into each one directly from the gateway with
no problem. my setup is as follows
Service provider public Cisco router --------- my router (has a
public IP) with port forwarding enabled on the ports I am interested in to the
meshbox at the private ip
(192.168.1.100) ------- (192.168.1.100-meshbox)
with host forwarding and port forwarding enabled to the computers I want to
reach. (the port forwarding on the mesh box have been left blank)
my main issues are this:
1:
On the three server 192.168.2.30, 192.168.2.60 and 192.168.2.90 for some reason
all the internet traffic seems to prefer 192.168.2.90 and do not see any of the
others.I tried turning off 192.168.2.90 and only having the server apache
runing on 192.168.2.30 but when someone queries the public addres or the domain
name they get hung up until I enable the server at the 192.168.2.90 address
then all works as it should. I have tried to reboot the gateway with all the
other servers shut off except 192.168.2.30 and still does not work I have also
tried to delete the mapping from the the gateway and only leaving 192.168.2.30 active.
For some reason it still does not work I can ping it fromthe gateway
get a webpage served locally using the 192.168.2.30 address, I can curl the
page from the gateway usng the the private adress but when I try from the
public address - nothing - nada - nulla - until I put back online
192.168.2.90 then all is okay i get it to actas it should.
the only other thing I have done is enabled port mapping but have
left them all blank. on the other hand, on my peer to peer computer which is on a nother
radio cell and private ip range 192.168.8.10 I cannot seem to get it to be seen
from the internet on the ports of interest mainly 4662 TCP and 4672 UDP
I have enabled the host forwarding to the this box from the gateway and can
ping the address of the box from the gateway but it still seems to have the
ports invisible from the internet. Please let me know of your experiences on
opening and closing ports in order to either abilitate or completely disabilitate
peer to peer operation also if you have some sugggestion on multiple servers in
the same subnet and how they can be seen suing a single public ip address please
let me have your experiences.

}}}

links Edit

http://winhelp2002.mvps.org/

http://winhelp2002.mvps.org/hosts.txt

Wireshark

Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.